Nautical Enamel Topside Paint
By A Mystery Man Writer
Last updated 04 Jun 2024
Shop Wholesale Marine for the lowest prices on Interlux Nautical Enamel. This one-part topside paint delivers professional results. Choose from 3 finishes.
Interlux Nautical Enamel - Gallon Nautical Enamels are one-part professional quality interior and exterior alkyd enamels. Economically priced and formulated to provide performance, value and reliability these finishes are durable and offers toughness, chemical resistance and excellent hide and wear characteristics. Nautical Enamels are ideal for decks, hulls and interiors in the marine environment. Nautical Enamels are available in a high gloss, semi gloss and flat finish and can be applied to any properly prepared fiberglass, metal or wood surfaces above the waterline, inside or out. Features & Benefits: Easy application High hiding characteristics Excellent flow and leveling Great stain resistance to grease, oil and water High solids and low V.O.C. For interior and exterior use ***WILL SHIP GROUND ONLY TO THE CONTIGUOUS 48 STATES ONLY*** Application Instructions HOW TO APPLY INTERLUX NAUTICAL ENAMEL Mixing Stir well before and during use. Cleaner Mineral Spirits or Naphtha Thinning: Do not thin Ventilation and Humidity Control Apply in dry, well ventilated conditions, Avoid excessively humid conditions, over 80% relative humidity. Brush Natural bristle brush Roller Use a solvent resistant small closed cell foam roller Airless Spray: Tip Size: 0.33 mm/13 thou. Pressure adjust as needed. Application Methods Brush Roller Airless Spray Preparation Bare Fiberglass Scrub the surface thoroughly with a stiff brush using soap and water. Flush with fresh water to remove the soap residue and allow surface to dry. Remove surface contamination by wiping down the surface with Mineral Spirits or Naphtha using the two-rag method. Fill any surface imperfections with approved filler for alkyd topside paint use. Sand the entire surface with 220-grit sandpaper until a flat matte finish is obtained. Wipe the sanding residue off the surface with Mineral Spirits or Naphtha using the two-rag method. If the surface is in poor condition and to achieve optimal results, use a primer approved for alkyd topside paints as per manufacturer’s instructions. Previously Painted Surface – Good Condition Remove all traces of loose paint by sanding the entire surface with 220-grit wet-or-dry sandpaper; wipe surface clean with Mineral Spirits or Naphtha using the two-rag method before and after sanding. To achieve optimal results, use a primer approved for alkyd topside paints as per manufacturer’s instructions. Previously Painted Surface – Poor Condition Completely remove old paint. After all old paint has been removed, follow preparation instructions for bare fiberglass. Bare Wood Scrub the surface thoroughly with a stiff brush using soap and water. Flush with fresh water to remove the soap residue and allow surface to dry. Remove surface contamination by wiping down the surface with Mineral Spirits or Naphtha using the two-rag method. Fill any surface imperfections with approved filler for topside paint use. Sand the entire surface with 220-grit sandpaper until a flat matte finish is obtained. Wipe the sanding residue off the surface with Mineral Spirits or Naphtha using the two-rag method. If the surface is in poor condition, and to achieve optimal results, use a primer approved for alkyd topside paints as per manufacturer’s instructions. Metals Apply a metal primer approved for alkyd topside paints as per manufacturer’s instructions. Do not apply Nautical Enamel directly to bare metal. Clear Epoxy Nautical Enamel cannot be applied directly to clear epoxy. Clear epoxy when drying create amine blush which must be removed prior to applying paint. Allow the epoxy to cure for 3-5 days in hot weather or 7 days in cold weather. Scrub the surface using soap and water using a stiff brush. Sand the surface using 80-grit sandpaper (preferably wet). Remove the sanding residue by wiping down the surface with Mineral Spirits or Naphtha using the two…
Interlux Nautical Enamel - Gallon Nautical Enamels are one-part professional quality interior and exterior alkyd enamels. Economically priced and formulated to provide performance, value and reliability these finishes are durable and offers toughness, chemical resistance and excellent hide and wear characteristics. Nautical Enamels are ideal for decks, hulls and interiors in the marine environment. Nautical Enamels are available in a high gloss, semi gloss and flat finish and can be applied to any properly prepared fiberglass, metal or wood surfaces above the waterline, inside or out. Features & Benefits: Easy application High hiding characteristics Excellent flow and leveling Great stain resistance to grease, oil and water High solids and low V.O.C. For interior and exterior use ***WILL SHIP GROUND ONLY TO THE CONTIGUOUS 48 STATES ONLY*** Application Instructions HOW TO APPLY INTERLUX NAUTICAL ENAMEL Mixing Stir well before and during use. Cleaner Mineral Spirits or Naphtha Thinning: Do not thin Ventilation and Humidity Control Apply in dry, well ventilated conditions, Avoid excessively humid conditions, over 80% relative humidity. Brush Natural bristle brush Roller Use a solvent resistant small closed cell foam roller Airless Spray: Tip Size: 0.33 mm/13 thou. Pressure adjust as needed. Application Methods Brush Roller Airless Spray Preparation Bare Fiberglass Scrub the surface thoroughly with a stiff brush using soap and water. Flush with fresh water to remove the soap residue and allow surface to dry. Remove surface contamination by wiping down the surface with Mineral Spirits or Naphtha using the two-rag method. Fill any surface imperfections with approved filler for alkyd topside paint use. Sand the entire surface with 220-grit sandpaper until a flat matte finish is obtained. Wipe the sanding residue off the surface with Mineral Spirits or Naphtha using the two-rag method. If the surface is in poor condition and to achieve optimal results, use a primer approved for alkyd topside paints as per manufacturer’s instructions. Previously Painted Surface – Good Condition Remove all traces of loose paint by sanding the entire surface with 220-grit wet-or-dry sandpaper; wipe surface clean with Mineral Spirits or Naphtha using the two-rag method before and after sanding. To achieve optimal results, use a primer approved for alkyd topside paints as per manufacturer’s instructions. Previously Painted Surface – Poor Condition Completely remove old paint. After all old paint has been removed, follow preparation instructions for bare fiberglass. Bare Wood Scrub the surface thoroughly with a stiff brush using soap and water. Flush with fresh water to remove the soap residue and allow surface to dry. Remove surface contamination by wiping down the surface with Mineral Spirits or Naphtha using the two-rag method. Fill any surface imperfections with approved filler for topside paint use. Sand the entire surface with 220-grit sandpaper until a flat matte finish is obtained. Wipe the sanding residue off the surface with Mineral Spirits or Naphtha using the two-rag method. If the surface is in poor condition, and to achieve optimal results, use a primer approved for alkyd topside paints as per manufacturer’s instructions. Metals Apply a metal primer approved for alkyd topside paints as per manufacturer’s instructions. Do not apply Nautical Enamel directly to bare metal. Clear Epoxy Nautical Enamel cannot be applied directly to clear epoxy. Clear epoxy when drying create amine blush which must be removed prior to applying paint. Allow the epoxy to cure for 3-5 days in hot weather or 7 days in cold weather. Scrub the surface using soap and water using a stiff brush. Sand the surface using 80-grit sandpaper (preferably wet). Remove the sanding residue by wiping down the surface with Mineral Spirits or Naphtha using the two…
White, Rust-Oleum Marine Coatings Topside Gloss Boat Paint, Quart
A single package, alkyd enamel designed for use on commercial or pleasure boats. Duralux marine enamel is also ideal for equipment, onshore and offshore oil rigs, bridges, tanks and most other structural objects. It fights rust and corrosion under moderate exposure to salt water, fuel oils and harsh cleaning solutions.
Duralux M720-1 Marine Paint 1 Gallon, White
Toplac Topside Paint
Rust-Oleum Marine Coatings Topside Paint Gloss White Enamel Oil-based Marine Paint (1-quart) in the Marine Paint department at
Duralux Marine Enamel - Signal Yellow 1 Gallon
TotalBoat - 365397 Wet Edge Marine Topside Paint for Boats, Fiberglass, and Wood (Largo Blue, quart)
Duralux Marine Paint - Spray Paint Enamels – Pro Solutions Direct
Pioneer Marine Quick Dry Enamel - Pioneer
Kush Camo Paint - Top Rated Dead Flat Marine Enamel – Kush Paint
Boat paint test - the best enamel paints in comparison
Ideal for use on fiberglass, wood or metal surfaces above the waterline Oil-based formula is flexible and applies easily with excellent leveling Dries
Rust-Oleum 207006-4PK Marine Topside Paint, Black, 32 Fl Oz (Pack of 4)
Recommended for you
-
Krylon COLORmaxx Spray Paint Semi-Gloss White04 Jun 2024
-
1 gal. i300 White Semi-Gloss Interior Paint04 Jun 2024
-
HOW TO PAINT A WALL USING ROLLER (CHINA WHITE SEMI GLOSS LATEX)PAANO MAGPINTURA GAMIT ANG ROLLER04 Jun 2024
-
PRESTIGE Paints Interior Paint and Primer In One, 1-Gallon, Semi04 Jun 2024
-
Stops Rust Protective Enamel Oil-Based Paint, 1 Quart, Semi-Gloss04 Jun 2024
-
Valspar 4000 Semi-gloss Swiss Coffee 7002-16 Latex Interior Paint04 Jun 2024
-
Satin or Semi-Gloss Paint, Which Is The Best Option for Your Home04 Jun 2024
-
BEHR PREMIUM 1 qt. White Semi-Gloss Enamel Interior/Exterior Cabinet, Door & Trim Paint 712004 - The Home Depot04 Jun 2024
-
BEHR PREMIUM 5 gal. #S510-7 Dark Denim Semi-Gloss Direct to Metal Interior/Exterior Paint 323005 - The Home Depot04 Jun 2024
-
5 gal. Ultra Pure White Semi-Gloss Enamel Exterior Paint & Primer04 Jun 2024
You may also like
-
The Ryker Bag PRO Official Tool Roll Organizer – 4 Detachable Tool Pouches + Wrench Organizer, Heavy Duty Tool Bags for men + women Roll Up Tool Bag04 Jun 2024
-
Star Wars SVG Galaxys Edge SVG Iron On Cricut Printable Cast04 Jun 2024
-
Wood Furniture Repair Kit- Set of 41 Laminate Vinyl Floor Repair Kit Wood Fillers,Floor Scratch Repair, Touch Up Markers, Restore Hardwood Scratches04 Jun 2024
-
Gamblin Oil Painting Mediums & Solvents at New River Art & Fiber04 Jun 2024
-
Segarty Yellow Tissue Paper for Gift Bags, 100 Sheets 14 x 20 Inch Easter Tissue Paper for Packaging, Birthday, Wedding, Baby Shower, Decorations, Bulk Wrapping Paper for Crafts DIY Pom Pom04 Jun 2024
-
1PCS 0.8mm Highlighters Markers Graffiti Pen On Black Paper White Ink Manga Markers for Drawing04 Jun 2024
-
50PCS Jewelry Accessories 9 Words/Flat/Round Head Pins Jewelry Connectors Making Components Supplies 14K Gold Plated Metal Pin04 Jun 2024
-
Mountain Stencils for Painting on Wood Burning Stencils and Patterns Reusable Nature Deer Tree Stencils for Crafts Canvas Furniture Wall Drawing04 Jun 2024
-
Heat Blower for Crafts, Shrink Wrap, Heat Shrink Tubing, Wire Connectors, Electrical Connectors, Epoxy Resin, Candle Making Heat Blower, for Shrinking04 Jun 2024
-
Christmas trees background - simple seamless vector texture. Gift wrapping paper design Stock Vector Image & Art - Alamy04 Jun 2024