FashionFlex Puff HTV Metallic Red 12x20 –

 Add a fun 3D look to any design with FashionFlex® Puff! FashionFlex® Puff is a brand new puff product line available in 14 colors- the most puff colors in the industry! This is super easy to use as you only need to press once to get that puff effect. It’s easy to weed and its pressure-sensitive carrier allows for easy
 Add a fun 3D look to any design with FashionFlex® Puff! FashionFlex® Puff is a brand new puff product line available in 14 colors- the most puff colors in the industry! This is super easy to use as you only need to press once to get that puff effect. It’s easy to weed and its pressure-sensitive carrier allows for easy repositioning. Results will vary depending on the material it is applied to. Application Instructions Blade – 45° Cut – Mirror image Temp –  All colors:255°F – *275°FVary Puff effect by increasing or decreasing temperature by 10°F within range.*Metallic: 275°F Pressure – Medium, even  Time – 12-14 secondsStart at 12.If more time is needed, press an additional 2 seconds.Metallic: 10 seconds. Peel – Peel hot.Remove the carrier and/or transfer sheet immediately.Metallic: Re-press for 4 seconds for maximum puff.  *We personally found (for metallic only) that doing 275 for 10 seconds, peeling cover sheet, then repressing for 10 seconds worked the best for us. CARE – Wash inside out, cold water, gentle cycle, tumble dry low. Applies to: Cotton, Uncoated Polyester, Fabric Blends, Polyester/Acrylic, and Similar Fabrics Excluding Nylon Special Precautions Cannot be layered. Remove carrier immediately after pressing. If the carrier or transfer sheet is left on, it can create inconsistencies in the puffed material. Color variation - During manufacturing, color variation can occur between rolls. This is especially true for Neon colors. CUT SETTINGS PLEASE NOTE: Every blade and machine is a little bit different- always remember to test cut! These cut settings are a starting point to be adjusted to your blade and machine. CRICUT Material: Iron-On Pressure: Default Blade: Fine-Point Blade SILHOUETTE Material: Heat Transfer, Smooth Blade:  3 Speed:  8 Force:  10 GRAPHTEC Speed: 8 Force: 18 We use a 45° blade. Clear plastic side needs to be face down while cutting. Peel up a corner of the carrier to determine this before cutting. Carrier can be shiny or matte depending on batch. Size is +/- 0.50 inch and +/-3% on length Colors of products may be different than what the screen on your device shows. TIP: Always perform a test cut prior to cutting a whole design Helpful tip-Specialty Materials recommends if your T shirt or material your are putting this HTV on says dry fit, Moisture Wicking, or is Gildan Ultra Cotton, use a spray bottle of rubbing alcohol and squirt the material where you are putting the design. Then rub it in a bit with a cloth and dry or even heat press it to dry then press the design. This is due to the material being a coated material, instead of an un coated material.  

Puff HTV Problems and How To Fix Them! Temperatures are Different

3D Puff Heat Transfer Vinyl - 20 x 36 (1 Yard) (Puff

Add a fun 3D look to any design with FashionFlex® Puff!, This is super easy to use as you only need to press once to get that puff effect. It’s easy

FashionFlex Puff HTV White 12x20

3D Super Puff Heat Transfer Vinyl - Metallic Red

FashionFlex Puff HTV Metallic Gold 12x20 –

3D Puff Heat Transfer Vinyl - 20 x 36 (1 Yard) (Puff

WRAPXPERT Puff Vinyl Heat Transfer Black 3D Puffy HTV

Red 3D Puff Heat Transfer Vinyl

Add a fun 3D look to any design with FashionFlex® Puff!, This is super easy to use as you only need to press once to get that puff effect. It’s easy

FashionFlex Puff HTV Burgundy 12x20 (Slightly darker shade of red)

When heat is applied, 3D puffs up to create a unique texture to letters and shapes. It can create an authentic look without using embroidery for the

FashionFlex 3D PUff HTV

FashionFlex PUFF HTV –

FASHIONFlex®PUFF – Specialty Materials